Topics Topics Help/Instructions Help Edit Profile Profile Member List Register  
Search Last 1 | 3 | 7 Days Search Search Tree View Tree View  
Route 6x6 Discussion Board * Shop Talk: Tech Tips and Q&A section * How do you seat a tire bead? < Previous Next >

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Bill Entringer (Billyboy)

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

I was checking the air in my tires today (regular Rawhides) and noticed the bead on one of the tires about to un-seat (there was about a 1/4 in. gap between the rim and bead). I tried airing up the tire to the maximum of 15psi but it wouldn't seat. Any ideas?

Thanks,
Bill
Top of pagePrevious messageNext messageBottom of page Link to this message

Eddie Beddingfield

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Bill, Things to do are 1. Unseat bead,use soap and water as lubricant, reair tire. 2. Make sure tire is warm, beads stretch better when warm. 3. Rawhides and RH3's are a pain to get to seat. The tire say,s 30 psi max to seat bead,but i have had to go high as 50psi before. 4. Leave tire on machine if higher pressure is needed,and be ready for bead to pop loudly. 5. Tires can be dangerous use cages if possible. Hope this helps.
Top of pagePrevious messageNext messageBottom of page Link to this message

Don Abernathey (Dla)

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Take a piece of rope and a bar/pipe/baseball bat etc. Put the rope around the middle of the tire and use the lever to twist it tight. Need to drop the air pressure way down first - almost flat. As squeeze the center of the tire in it will flex the beads out.
Top of pagePrevious messageNext messageBottom of page Link to this message

the amazing roadwolf

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

hey billyboy, you can try usin a tie down wrachet around tha circumference of the tire. if that fails you can sumerge tha whole tire in water and seat it that way. juss rememba tha let all tha water out.
Top of pagePrevious messageNext messageBottom of page Link to this message

liflod (Liflod)

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Clean the beads and rim with acetone or some type of cleaner and use black silicone for lubricant and it will also keep the bead seated once it sets up.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jon

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Hi, I had the same problem with rawhide3s tried most of the above techniques. The max pressure stated on the tire is 15psi to seat bead. I was wondering how much above the max presure you can go safely?? I had up to 25psi & still wouldn't bead on the deep side of rim. thanks
Top of pagePrevious messageNext messageBottom of page Link to this message

Russell Lee (Bigkodiak)

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Jon,
Put the full 15 psi in then set the tire in a sunny place on a warm day. It will seat.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tom Pike

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Friend of mine pumps them up to 30 psi and puts them in the hot sun to seat his. I haven't had the guts to pump them up that much.
Top of pagePrevious messageNext messageBottom of page Link to this message

Eddie Beddingfield

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Jon, The way I went to 50 psi is. 1- bled my compressor to 0 psi. 2-Locked air chuck on valve stem. 3-Turned compressor on at compressor watching gauge and keeping as for away as possible. 4- Be ready for loud bang and turn compressor off. Rawhides will not seat on wheels with a beadlock rolled into them very easily. 15 psi would probably seat them on regular golf cart rims. This is only a way I have seated tire beads, it sure isnt recomended by me. Tires can be dangerous!!!!!!!!!!!!!!!
Top of pagePrevious messageNext messageBottom of page Link to this message

argogeru

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

JOn,
I have ran mine up to 45 lb. before to get them to seat. Make sure to put some soapy water on the bead so it pops on better. On the trail when a bead comes off i wipe the mud off the bead and use a portable air tank to reseat the tire, normally their is still a little mud and water on the bead but that seems to help it seat. but be aware if you do this on the trail that when it does seat it will spit mud and dirt out of the bead and go all over you, so protect your eyes, I almost learned the hard way. good luck.
Top of pagePrevious messageNext messageBottom of page Link to this message

John Martin

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

I like to use a little soapy water to act as a lube to help the tire pop over the safety bead on the rim. I have had to pressure up the tire more than I would have liked to more than a couple of times, but haven't had one blow-up yet, knock on wood! To be safe if you just can't get it, take it to a tire shop where they can at least use a tire cage to keep it from hurting somebody. Goodluck and be careful.
Top of pagePrevious messageNext messageBottom of page Link to this message

David Keeso (Argomag)

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

As someone who tends to go very hard on tires, what is the bead that you are talking about. I should know, but I don't. Help Please!
Top of pagePrevious messageNext messageBottom of page Link to this message

david berger (Davidrrrd)

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

DAVID KEESO, THE BEAD IS THE PART OF THE TIRE THAT TOUTCHES THE RIM, PART OF WITCH WIL LOCK INSIDE OF A RING INSIDE OF THE RIM DESIGNED TO HOLD THE TIRE BEAD, AND IF THATS NOT CONFUSING ENOPH THAT RAISED PORTION OF THE RIM I HAVE DESCRIBED AS A RING IS CALED A BEAD BY SOME FOLKS, BEADLOCK BY OTHERS, ??RIGHT GUYS
Top of pagePrevious messageNext messageBottom of page Link to this message

Eddie Beddingfield

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

David, some wheels have a bead rolled into both halves . Argo wheels have this and maybe Max also.Cheaper golf cart wheels usually dont ,and these seat very easily.Unfortunatly they roll off just as easily.To see the bead rolled into the rim look at where the tire and wheel meet when aired up ,now move in toward the center of rim about 3/4 of an inch.This hump is what the tire bead must slide over to seat. FYI a few years ago Bassett wheel made extreme bead wheels , they took over 120 psi to seat beads professional tire shops had people killed seating beads. Always take precautions Eddie
Top of pagePrevious messageNext messageBottom of page Link to this message

Ted S.

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Use starting fluid. Wipe the bead clean,shoot a little in and flick a lit match at it. There is a whoosh pop and you are back running. The fire inside will burn out in about 2 seconds and doesnt get hot enough to hurt the tire.
Top of pagePrevious messageNext messageBottom of page Link to this message

Pete Cagle (Petec)

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

never seen it work have tried it dont use unless it is a last resort
Top of pagePrevious messageNext messageBottom of page Link to this message

argogeru

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

I did all of my tires with starting fluid to seat them on the bead because the tire shop couldnt do it because they were off the rim for 2 years and the beads were to close together. Needless to say I agree with pete, last resort. one good thing though about the starting fluid is if you have any holes in the tires, the flames shooting out will show you exzacly were you need a plug or patch!
Top of pagePrevious messageNext messageBottom of page Link to this message

david berger (Davidrrrd)

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

i'd say don't try it, i did it before and one of the tires blew off the rim and the tire and rim sailed high enoph into the air that when i found it was gon and for some reason i looked up it was still aprox 30 feet up and burning! it hit my car and dented the hood, and all my naybors where running too see what the "BOOM" was!
i still feal like an ideot for that one,
seriosly, try somthin els,
Top of pagePrevious messageNext messageBottom of page Link to this message

John Martin

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

They don't call it an ether bomb for nothing!! You have to be really careful and not use to much ether or you will have too big-a-bomb. Takes a little practice to get the hang of it and I don't recommend it. If you use somekind of lube (soapy water) to help to tire slide on the rim you should be able to get it with air psi. Be careful whatever way you try.
Top of pagePrevious messageNext messageBottom of page Link to this message

Don Abernathey (Dla)

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

I guess I don't understand why this appears to be rocket science to some of you. You don't need explosives. All you need is a means of constricting the center of the tire. I've done this before with nothing more than a piece of cheesy rope and short chunk of rebar. I then proceeded to pump up the tire with a hand pump. Its really not that hard folks.
Top of pagePrevious messageNext messageBottom of page Link to this message

Eddie Beddingfield

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Don , I'll send you a ARGO rim and a 22" Rawhide III tire ,knock yourself out.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bknight (Bknight)

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Beading a tire, everyone has a different method of doing it. I agree, trying to seat a tire bead is a pain. I've found that using some sort of lube, whether it's soap and water or some of that blue goop from a garage that changes tires all the time is a key. I've found that when changing tires on my Max that after pumping 15 psi into them that bouncing them from mid body level like a ball while spinning them around helps set a bead. What I did was set one side then let the pressure out..put some more soap on that side that didn't set all the way..pump them up again and keep on bouncing. Within 5 minutes for each tire and everything was seated properly. I did have one tire that just wouldn't seat so I took it to a tire shop, and they placed it in a tire cage, hooked the air chuck to it and then a cone type device that blasted it with air and pow! seated both beads almost instantaneously.
Top of pagePrevious messageNext messageBottom of page Link to this message

argogeru

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

don,
I would half to see that to believe it, A HAND PUMP?! come on.
Top of pagePrevious messageNext messageBottom of page Link to this message

matt435

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Guy's this string is getting almost as good as the "creeking in a max" hee... hee....
Top of pagePrevious messageNext messageBottom of page Link to this message

Al

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Don,
ATV tires are thicker and wider, and more difficult to seat than any other tire, maybe you did it on a trailer tire, or a lawn tractor tire. Even car tires are easier than ATV tires.

Under nothing but ideal conditions could you do it with a hand pump. Sometimes the beads on the tire are nearly touching each other, so even when you put a rope or ratchet strap around the center, the tire will just not spread. Or, sometimes it just wrinkles up around the spot where you are twisting the turnicate, or ratchet strap. In these cases, a hand pump would do nothing. You have to have a high speed, high volume of air to get the tire to swell up and catch both sides of the rim. One thing that helps is a tire chuck that holds itself on the valve stem so you can try to use your hands to persuade the beads to seal, of course you don't put your fingers between the tire and the rim!

In addition, it sounds like most of these people
had the beads started: where they were holding air. At this point you remove the rope, and overinflate them, but in many cases, the beads, even when lubed, will not seat.

I have put WAY over 15 pounds in these tires to seat them. I always do what BKnight said, bounce them like a basketball (while they are overinflated), and eventually, they all surrender.

Al
Top of pagePrevious messageNext messageBottom of page Link to this message

mr. tinker

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, February 23, 2005 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

just a note. if you remove valve core you will get larger quantity of air through valve stem.
Top of pagePrevious messageNext messageBottom of page Link to this message

Brad Morcom
New member
Username: Stihl1

Post Number: 2
Registered: 12-2005
Posted From: 24.177.157.87

Rating: N/A
Votes: 0 (Vote!)

Posted on Wednesday, December 14, 2005 - 05:53 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

On large tires we use ether or aqua-net hairspray and an ignition source. On big tires I am comfortable but on a small tire I would only use it as a last resort.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sean McConnell
Member
Username: Bookm

Post Number: 36
Registered: 09-2005
Posted From: 69.159.216.86

Rating: N/A
Votes: 0 (Vote!)

Posted on Thursday, December 15, 2005 - 05:00 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

LOL! I've seen them seat Monster Truck tires by "exploding" them on with hair spray (now illegal I believe).

When working as a kid in a Uniroyal dealership, we used a steel tubular ring with a quick-release collar that would release a quick blast of air through holes dispursed around the ring, in the direction of the tire bead. The bottom bead had to be seated first, then the air pressure would blast the upper bead into place (after a thorough soaping of the tire and rim). A good 'ole beating with a rubber mallet encouraged the final bead seat with a loud POP!! Then the air pressure could be brought back down to proper levels. I plan to fab some smaller rings to suit these smaller tires/rims and hope for the best.

The air chuck mentioned above is a must. Keep you fingers clear, and wear eye protection! Any little bit of crud sitting on the tire will become a tiny missile when she pops on!

Also, though I never needed to try it, we did have a foam ring lying around (looked a little like a pool noodle). I believe you were to soak it in soapy water, then apply it to the gap between the rim and tire. This would create the needed air-lock. The "noodle" would eventually be squeezed out of the gap as the tire inflates. Every time I struggle with a small-tire bead problem, I try to think of a way to make one of these rings, but haven't figured it out yet :-(

If you don't have a good high-volume compressor, you're not likely to have much success. And you really need a way to secure the rim on top of a pedestal, so you can twist the tire down to seat the lower bead first. Then, with the air hose chuck in place, you can often pull straight up on the tire to "catch" the upper bead.

... and don't even TRY to stay clean!!!
Top of pagePrevious messageNext messageBottom of page Link to this message

philip w.cox
Intermediate Member
Username: Philipatmaxfour

Post Number: 70
Registered: 01-2005
Posted From: 64.228.3.164

Rating: N/A
Votes: 0 (Vote!)

Posted on Friday, December 16, 2005 - 06:10 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

TOO GOOD TO MISS! --The last few posts on this thread are posted by people who obviously know what they are talking about,but I hope everybody went back up 12 posts to reade about David Bergers " Flaming Flying Tire" What a good belly laugh. Thanks David. W.Philip Cox
Top of pagePrevious messageNext messageBottom of page Link to this message

Larry Houghton (Unregistered Guest)
Unregistered guest
Posted From: 69.90.48.254

Rating: N/A
Votes: 0 (Vote!)

Posted on Friday, December 16, 2005 - 09:38 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only) Ban Poster IP (Moderator/Admin only)

Most guys doing tires all the time like truck tires have a portable air tank which hooks on the edge of the rim and gives the tire a big shot of air and pops the bead onto the rim. Safe and easy,leaves you with your eyelashes.I have also just used some chassis grease to help make a seal between rim and tire, tire and smooth floor, works good especially on a few truck tires.

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Action: