Is this the orginal engine ?

Route 6x6 Discussion Board: Shop Talk: Tech Tips and Q&A section: Is this the orginal engine ?
Top of pagePrevious messageNext messageBottom of pageLink to this message   By Roger Walsh on Unrecorded Date: Edit

I have a Attex 208/TT early 70s model .It has a
8hp briggs . It seems a little under powered . My
question is ? Was this the factory powerplant ? if
not how big of a engine could i install without
harming the running gear . I bought this rig two
years ago it was a total basket case , and I have
totally restored it . I fabercated a roll bar as
well as new hubs and four axles and replaced all
the bearings and rebuilt the engine .It looks and
runs good ......Roger in Oregon

Top of pagePrevious messageNext messageBottom of pageLink to this message   By david berger (Davidrrrd) on Unrecorded Date: Edit

roger my first attex was a 208-tt, yes thats the right engine, and yes it's underpowered, i put a 1972 rupp T N T 440cc 2-stroke in it!
it held up ok,
but it's too much power,(could kill yah)
i sugest a rupp 340cc(tokiyo hatsodki)

Top of pagePrevious messageNext messageBottom of pageLink to this message   By pete6x6 on Unrecorded Date: Edit

Roger,

No that is not the original powerplant. It more than likely had a jlo two cycle powerplant in it displacing about 200-300cc's or so. Richard has them if you want to buy one. Richard also sold one not too long ago a old wild wolf I believe with a 295 jlo two-stroke.

Top of pagePrevious messageNext messageBottom of pageLink to this message   By liflod (Liflod) on Unrecorded Date: Edit

According to my owner's manual, the 208tt had a 12.5 hp briggs in it.

Top of pagePrevious messageNext messageBottom of pageLink to this message   By david berger (Davidrrrd) on Unrecorded Date: Edit

pete6x6 & liftlod, the 8hp brigs is the right engine, the 208-tt also had as an option a generator for 110v ac
as to the 12hp i guess it might have bin a diferent modle year than mine or rogers, mine is a 71 modle year.
as to the single cil engine swap, thats ok i guess if your kids goin to drive it, but it's not a good swap as ther underpowered also and you wont be satisfyed, if your going to spend the time and the money on a engine swap you might as well get it right the first time, i stand by my 340cc twin cyl,recamendation as the least amont of power, " just enoph in all situations"
loaded down with cargo , pasengers and or hard day of driving and the jlo will be pushed too far and overheat, no problem with the 340cc,
it'l eat it up.

Top of pagePrevious messageNext messageBottom of pageLink to this message   By pete6x6 on Unrecorded Date: Edit

Dave,

Agreed 340cc is better :) I'd cram a v8 in mine if I could :)

Top of pagePrevious messageNext messageBottom of pageLink to this message   By roger walsh on Unrecorded Date: Edit

I bought a attex that was not rebuildable , but i
stripped down and got a ton of parts that i could
use on my 208/tt model . My fist question is : the
transmission is slightly differant. It's a power
transmission series 7000 ser no. 0254 . it has a
transmission between the steering disks on the
shaft is this a fwd/rev transmission , is it easy
to rebuild ? the transmission in my rebuilt
208/tt does not have one in the center between the
disks. my second question : where can i get pads
for calipers it takes 8 all together . do know how
much they cost too ? ......roger in oregon

Top of pagePrevious messageNext messageBottom of pageLink to this message   By roadwolf on Unrecorded Date: Edit

liflod, the attex model 225 had a 12.5 hp ccw (canadian curtis wright) 2 stroke. hey pete6x6, i seem to remember you. weren't you the guy buildin' up a attex?

Top of pagePrevious messageNext messageBottom of pageLink to this message   By pete6x6 on Unrecorded Date: Edit

Liflod,

The Attex line used several trannys including the t20. Richard more than likely has parts for the 7000 and it's not a bad tranny either. Richard prolly has the brake pads also or ones you can substitute. I've found mixed results with the old brakes. If you improve the powerplant the brakes ned improvement also. I am currently working on replacing the standard brake system in my attex with hydralic discs. Roadwolf yes it's me I'm still working on the old Attex coming along good though I just ordered a muffler from Richard. Good thing Richard doesn;t live closer I'd be buying stuff from him all day :). I've been out of the 6x6 scene for awhile after Sept 11th I lost my Navy job but that ain't stoppin me I'm gonna finish this thing and be a pete c's ride in april then up in ny in july!

Top of pagePrevious messageNext messageBottom of pageLink to this message   By mark harding (Promoza) on Unrecorded Date: Edit

hello sorry but this is not about a motor i know of the ride in new york but what is the other ride(the pete c)ride ???? any help thanks
mark

Top of pagePrevious messageNext messageBottom of pageLink to this message   By pete6x6 on Unrecorded Date: Edit

Mark,

Pete C the moderator of this discussion group usually has a get together in Early April in Salem NJ. I did not get to go last year but will be going this year if he has it again.


Add a Message


This is a public posting area. If you do not have an account, enter your full name into the "Username" box and leave the "Password" box empty. Your e-mail address is optional.
Username:  
Password:
E-mail:

Administrator's Control Panel -- Board Moderators Only
Administer Page | Delete Conversation | Close Conversation | Move Conversation